ASROCK Z68 Extreme3 Gen3 Bedienungsanleitung

1Z68 Extreme3 Gen3User ManualVersion 1.0Published July 2011Copyright©2011 ASRock INC. All rights reserved.

10CAUTION!1. About the setting of “Hyper Threading Technology”, please check page 60.2. This motherboard supports Dual Channel Memory Technology. Be

1110. ASRock Instant Flash is a BIOS fl ash utility embedded in Flash ROM. This convenient BIOS update tool allows you to update system BIOS without e

1216. ASRock On/Off Play Technology allows users to enjoy the great audio ex-perience from the portable audio devices, such like MP3 player or mobile

131.3 Motherboard Layout 1 ATX 12V Power Connector (ATX12V1) 22 64Mb SPI Flash 2 1155-Pin CPU Socket 23 Chassis Fan Connector (C

141.4 I/O Panel* There are two LED next to the LAN port. Please refer to the table below for the LAN port LED indications.

15 To enable Multi-Streaming function, you need to connect a front panel audio cable to the front panel audio header. After restarting your comput

16Chapter 2: Installation This is an ATX form factor (12.0" x 8.6", 30.5 x 21.8 cm) motherboard. Before you install the motherboard, study t

172.3 CPU Installation For the installation of Intel 1155-Pin CPU, please follow the steps below.Before you insert the 1155-Pin CPU into the socket,

18Pin1alignment key alignment key Pin11155-Pin CPU1155-Pin SocketStep 3. Insert the 1155-Pin CPU:Step 3-1. Hold the CPU by the edge where is marke

192.4 Installation of CPU Fan and Heatsink This motherboard is equipped with 1155-Pin socket that supports Intel 1155-Pin CPU. Please adopt the typ

2Copyright Notice:No part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, exce

202.5 Installation of Memory Modules (DIMM) This motherboard provides four 240-pin DDR3 (Double Data Rate 3) DIMM slots, and supports Dual Channel Me

21Installing a DIMMPlease make sure to disconnect power supply before adding or removing DIMMs or the system components. Step 1. Unlock a DIMM sl

222.6 Expansion Slots (PCI and PCI Express Slots)There are 2 PCI slots and 4 PCI Express slots on this motherboard. PCI slots: PCI slots are used

232.7 SLITM and Quad SLITM Operation GuideThis motherboard supports NVIDIA® SLITM and Quad SLITM (Scalable Link Interface) technology that allows you

24Step4. Connect a VGA cable or a DVI cable to the monitor connector or the DVI connector of the graphics card that is inserted to PCIE2 slot. Step3.

252.7.2 Driver Installation and SetupInstall the graphics card drivers to your system. After that, you can enable the Multi-Graphics Processing Unit (

26 For Windows® VistaTM / VistaTM 64-bit / 7 / 7 64-bit OS: (For SLITM and Quad SLITM mode) A. Click the Start icon on your Windows taskbar. B. From

27 1. If a customer incorrectly confi gures their system they will not see the performance benefi ts of CrossFireXTM. All three CrossFireXTM c

28CrossFire BridgeStep 3. Connect the DVI monitor cable to the DVI connector on the Radeon graphics card on PCIE2 slot. (You may use the DVI to D-S

29 The Catalyst Uninstaller is an optional download. We recommend using this utility to uninstall any previously installed Catalyst drivers prio

3Contents1 Introduction ... 51.1 Package Contents ...

30 Although you have selected the option “Enable CrossFireTM”, the CrossFireXTM function may not work actually. Your computer will automatically r

312. If you have installed onboard VGA driver from our support CD to your system already, you can freely enjoy the benefi ts of dual monitor

32Surround Display FeatureThis motherboard supports surround display upgrade. With the internal VGA output support (DVI-D, D-Sub and HDMI) and externa

33 For Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS: Right click the desktop, choose “Personalize”, and select the “Display Settings”

34USB 2.0 header (9-pin, black) CIR header (4-pin, gray) 2.10 ASRock Smart Remote Installation GuideASRock Smart Remote is only used for ASRock mother

35* ASRock Smart Remote is only supported by some of ASRock motherboards. Please refer to ASRock website for the motherboard support list: http://ww

362.11 Jumpers Setup The illustration shows how jumpers are setup. When the jumper cap is placed on pins, the jumper is “Short”. If no jumper cap is p

372.12 Onboard Headers and ConnectorsOnboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placi

38USB 2.0 Headers Besides four default USB 2.0 (9-pin USB6_7) ports on the I/O panel, there (see p.13 No. 29) are four USB 2.0 headers on thi

39System Panel Header This header accommodates(9-pin PANEL1) several system front panel (see p.13 No. 20) functions. Connect the power switch, r

43 UEFI SETUP UTILITY ... 533.1 Introduction ...

40Chassis and Power Fan Connectors Please connect the fan cables (4-pin CHA_FAN1) to the fan connectors and (see p.13 No. 23) match the blac

41ATX Power Connector Please connect an ATX power (24-pin ATXPWR1) supply to this connector. (see p.13 No. 8)12 1241320-Pin ATX Power Supply

42Reset Switch Reset Switch is a smart switch,(RSTBTN) allowing users to quickly reset(see p.13 No. 17) the system.Clear CMOS Switch Clear

432.14 Dr. DebugDr. Debug is used to provide code information, which makes troubleshooting even easier. Please see the diagrams below for reading the

44 0x37 Post-Memory North Bridge initialization is started 0x38 Post-Memory North Bridge initialization (North Bridge module specifi c) 0x39 Po

45 0x62 Installation of the South Bridge Runtime Services 0x63 CPU DXE initialization is started 0x64 CPU DXE initialization (CPU module spec

46 0xA6 SCSI Detect 0xA7 SCSI Enable 0xA8 Setup Verifying Password 0xA9 Start of Setup 0xAA Reserved for ASL (see ASL Status Codes secti

472.15 Serial ATA (SATA) / Serial ATAII (SATAII) Hard Disks Installation This motherboard adopts Intel® Z68 chipset that supports Serial ATA (SATA) /

482.17 Hot Plug and Hot Swap Functions for SATA / SATAII HDDs This motherboard supports Hot Plug and Hot Swap functions for SATA / SATAII in RAID / A

49 Caution1. Without SATA 15-pin power connector interface, the SATA / SATAII / SATA3 Hot Plug cannot be processed.2. Even some SATA / SATAII / S

5Chapter 1: IntroductionThank you for purchasing ASRock Z68 Extreme3 Gen3 motherboard, a reliable motherboard produced under ASRock’s consistently st

50 How to Hot Plug a SATA / SATAII / SATA3 HDD:Points of attention, before you process the Hot Plug:Please do follow below instruction sequence to pro

51ctor. 2.20 Driver Installation GuideTo install the drivers to your system, please insert the support CD to your optical drive fi rst. Then, the driv

522.22 Installing Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit / XP / XP 64-bit Without RAID Functions If you want to install Windows® 7 / 7 64

53Chapter 3: UEFI SETUP UTILITY3.1 IntroductionThis section explains how to use the UEFI SETUP UTILITY to confi gure your system. The UEFI chip on the

543.1.2 Navigation Keys Please check the following table for the function description of each navigation key. Navigation Key(s) Function Description

553.3 OC Tweaker ScreenIn the OC Tweaker screen, you can set up overclocking features.Advanced Turbo 50 You can use this option to increase your sys

56Intel Turbo Boost Technology Use this item to enable or disable Intel Turbo Boost Technology. Turbo Boost allows processor cores to run faster tha

57CAS# Latency (tCL) Use this item to change CAS# Latency (tCL) Auto/Manual setting. The default is [Auto]. RAS# to CAS# Delay (tRCD) Use this item to

58ODT NOM (CHA) Use this item to change ODT NOM (CHA) Auto/Manual setting. The de-fault is [Auto]. ODT WR (CHB) Use this item to change ODT WR (CHB) A

59Setting wrong values in this section may cause the system to malfunction.3.4 Advanced ScreenIn this section, you may set the confi gurations for the

61.2 Specifications Platform - ATX Form Factor: 12.0-in x 8.6-in, 30.5 cm x 21.8 cm - Premium Gold Capacitor design (100% Japan-made high-qualit

603.4.1 CPU ConfigurationIntel Hyper Threading Technology To enable this feature, it requires a computer system with an Intel processor that suppor

61CPU Thermal Throttling You may select [Enabled] to enable CPU internal thermal control mechanism to keep the CPU from overheated.Intel Virtualiza

623.4.2 North Bridge Configuration Low MMIO Align Low MMIO resources align at 64MB/1024MB. The default value is [1024M]. VT-d Use this to enabl

63 DVMT Mode SelectUse this option to adjust DVMT mode. The default value is [DVMT Mode].DVMT (Dynamic Video Memory Technology) is an architecture th

643.4.3 South Bridge ConfigurationRestore on AC/Power LossThis allows you to set the power state after an unexpected AC/power loss. If [Power Off] i

65Good Night LED Enable this option to turn off Power LED and Port80 LED when the system is power on. The keyboard LED will also be turned off in S1,

663.4.4 Storage ConfigurationSATA Mode Use this to select SATA mode. Confi guration options: [IDE Mode], [AHCI Mode], [RAID Mode] and [Disabled]. The

673.4.5 Super IO ConfigurationSerial Port Use this item to enable or disable the onboard serial port. Serial Port Address Use this item to set t

683.4.6 ACPI ConfigurationSuspend to RAMUse this item to select whether to auto-detect or disable the Suspend-to-RAM feature. Select [Auto] will enabl

693.4.7 USB ConfigurationUSB 2.0 ControllerUse this item to enable or disable the use of USB 2.0 controller. USB 3.0 ControllerUse this item to enabl

7 - Supports Auto Lip Sync, Deep Color (12bpc), xvYCC and HBR (High Bit Rate Audio) with HDMI (Compliant HDMI monitor is required) (see CAU

703.5 Hardware Health Event Monitoring ScreenIn this section, it allows you to monitor the status of the hardware on your system, including the param

713.6 Boot ScreenIn this section, it will display the available devices on your system for you to confi g-ure the boot settings and the boot priority.

723.7 Security ScreenIn this section, you may set or change the supervisor/user password for the system. For the user password, you may also clear it.

733.8 Exit ScreenSave Changes and ExitWhen you select this option, it will pop-out the following message, “Save confi guration changes and exit setup?”

74Chapter 4: Software Support 4.1 Install Operating System This motherboard supports various Microsoft® Windows® operating systems: 7 / 7 64-bit / Vi

75Installing OS on a HDD Larger Than 2TBThis motherboard is adopting UEFI BIOS that allows Windows® OS to be installed on a large size HDD (>2TB).

8 - 2 x SATA3 6.0Gb/s connectors - 1 x IR header - 1 x CIR header - 1 x COM port header - 1 x HDMI_SPDIF header - 1 x Power LED header - CPU/Cha

9 Hardware - CPU Temperature Sensing Monitor - Chassis Temperature Sensing - CPU/Chassis/Power Fan Tachometer - CPU/Chassis Quiet Fan (Allow Chas