ASROCK IMB-147 Bedienungsanleitung

1IMB-147User ManualVersion 1.0Published January 2013Copyright©2013 ASRock INC. All rights reserved.

101 Backlight & Amp Volume Control Header (BLT_VOL1)2 LVDS Panel Connector (LVDS1)3Panel Power Jumper (PNL_PWR1)4Inverter Power Control Header (BL

111.5 I/O Panel* There are two LEDs on each LAN port. Please refer to the table below for the LAN port LED indications.ACT/LINKLEDSPEEDLEDLAN Port

12Chapter 2: InstallationThis is a Mini-ITX form factor motherboard. Before you install the mother-board, study the conguration of your chassis t

132.1 Installing Memory Modules (DIMM)This motherboard provides two 204-pin DDR3 (Double Data Rate 3) SO-DIMM slots.Step 1. Align a DIMM on the slo

142.2 Expansion Slots (PCI and PCI Express Slots)There is 1 PCI slot and 1 mini PCI Express slot on this motherboard.PCI Slot: PCI slot is used to i

15Serial ATA2 Connectors(SATA2_1: see p.10, No. 10)(SATA2_2: see p.10, No. 11)These two Serial ATA2 (SATA2) connectors sup-port SATA data cables for i

16SATA Power Connector(4-pin SATA_PWR1)(see p.10, No. 8)2.4 Power ConnectorsATX 12V Power Connector(4-pin ATX12V1)(see p.10, No. 7)Please connect a p

172.5 Installing the System PanelConnect the power switch, reset switch and system status indicator on the chassis to this header according to

182.6 Onboard Headers and ConnectorsOnboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Plac-

19Serial Port Header(10-pin COM4)(see p.10, No. 19)(10-pin COM5)(see p.10, No. 20)(10-pin COM6)(see p.10, No. 21)PIN Signal Name PIN Signal Name2 NC 1

2Copyright Notice:No part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, exce

20Inverter Power Control Connector(5-pin BLT_PWR3)(see p.10, No. 4)PIN Signal Name1 +12V2GND3B/L ENABLE4 B/L ADJUST5 +5V1Backlight & Amp Volume Co

211 2PIN Signal Name PIN Signal Name9 RED 10 GND7GRN 8GND5 BLUE 6 GND3 HSYNC 4 VSYNC1 DDC_CLK 2 DDC_DATVGA Header(10-pin VGA_H1)(see p.10, No. 28)

22Clear CMOS Jumper(3-pin CLRCMOS1)(see p.10, No. 18)Clear CMOSDefaultCLRCMOS1 allows you to clear the data in CMOS. To clear and reset the system par

23Panel Power Jumper(3-pin PNL_PWR1)(see p.10, No. 3)1-2 : +3V2-3 : +5VATX/AT Mode Jumper(3-pin PWR_JP1)(see p.10, No. 13)1-2 : AT Mode2-3 : ATX Mode

242.8.1 Installing Windows® 7 without RAID Using AHCI ModeSTEP 1: Set Up UEFI.Press <F2> or <Delete> at system POST. Set AHCI Mode in UE

252.9 Installing DriversThe Support CD that comes with the motherboard contains necessary driv-ers and useful utilities that enhance the motherboard’

26SATA 7-pinconnectorThe 1x4-pin conventional power connector (White) should be connected to a power supplyThe SATA 15-pin power connector (Black) sho

27Points for attention, before you process Hot Plug:1. Without the SATA 15-pin power connector interface, Hot Plug cannot be processed.2. Even tho

28 How to Hot Plug an HDD:Please follow the instructions below to process Hot Plug. Improper procedures will cause the HDD damage and data loss.Connec

29 How to Hot Unplug an HDD:Please follow the instructions below to process Hot Unplug. Improper procedures will cause the HDD damage and data loss.Un

3Contents1. Introduction ... 5 1.1 Package Contents ...

30Chapter 3: UEFI SETUP UTILITY3.1 IntroductionThis section explains how to use the UEFI SETUP UTILITY to congure your system. The UEFI ch

313.1.2 Navigation KeysUse < > key or < > key to choose among the selections on the menu bar, and use < > key or <

323.2 Main ScreenWhen you enter the UEFI SETUP UTILITY, the Main screen will appear and display the system overview.

333.3 Advanced ScreenIn this section, you may set the congurations for the following items: CPU Configuration, Chipset Configuration, Storage Co

343.3.1 CPU CongurationHyper-ThreadingTo enable this feature, a computer system with an Intel processor that supports Hyper-Threading technol

353.3.2 Chipset CongurationPanel Type SelectionUse this to select a panel type.Display Boot TypeUse this to select the video device which wi

363.3.3 Storage CongurationOnboard SATAII ModeUse this to select the SATA mode for SATA2_1 and SATA2_2 ports. Conguration options: [IDE Mode] and [

373.3.4 Super IO CongurationCOM1 PortUse this to enable or disable COM1 port.COM1 Port AddressUse this to set the address for COM1 port.COM2 PortUse

38LPT1 PortUse this to enable or disable LPT1 port.LPT1 Port ModeUse this to set the mode for LPT1 port.LPT1 Port AddressUse this to set the address f

393.3.5 ACPI CongurationSuspend to RAMUse this to select whether to auto-detect or disable Suspend-to-RAM. Select [Auto] to enable if the O

43. UEFI SETUP UTILITY ... 30 3.1 Introduction ...

403.3.6 USB CongurationUSB 2.0 ControllerUse this to enable or disable the USB 2.0 controller.Legacy USB SupportUse this to select legacy support

413.4 Hardware Health Event Monitoring ScreenThis section allows you to monitor the status of the hardware on your sys-tem, including the parameters

423.5 Boot ScreenThis section displays the available devices on your system for you to con-gure the boot settings and the boot priority.Setup Prompt

433.6 Security ScreenIn this section you may set or change the supervisor/user password for the system. You may also clear the user password.

443.7 Exit ScreenSave Changes and ExitWhen you select this option the following message, “Save congu-ration changes and exit setup?” will pop

51. IntroductionThank you for purchasing ASRock IMB-147 motherboard, a reliable moth-erboard produced under ASRock’s consistently stringent quality c

61.2 SpecicationsForm FactorDimensions Mini-ITX (6.7-in x 6.7-in)Processor SystemCPUIntel® Dual-Core AtomTM CedarView Processor D2550/N2600/N2800Cor

7 * For detailed product information, please visit our website: http://www.asrock.comRear I/OVGA 1 x D-Sub HDMI 0DVI-I/D 0Display Port 0Ethernet 2U

81.3 Unique FeaturesASRock Instant Flash ASRock Instant Flash is a BIOS ash utility embedded in Flash ROM. This convenient BIOS update tool

91.4 Motherboard Layout56DC1 2V1DDR3_A1DDR3_B1PCI1BUZ Z1CMOSBatte ryRJ -45USB 2.0T: USB1B: USB0RJ -45USB 2.0T: USB3B: USB2IMB-147COM3VGA1COM2COM1Desi